EFFECT OF STEAM ACTIVATION TEMPERATURE ON THE PORE STRUCTURE OF SHARGUN COAL (SURKHANDARYA, UZBEKISTAN): COMPARISON OF THE 600 AND 850 °C REGIMES

Authors

  • S. M. Isayev Shift engineer, ACWA Operation Company, Chirchiq, Uzbekistan, Professor, Department of Artificial Intelligence and Natural Sciences, University of Geological Sciences, Tashkent, Uzbekistan Author
  • M. Qudratov Shift engineer, ACWA Operation Company, Chirchiq, Uzbekistan, Professor, Department of Artificial Intelligence and Natural Sciences, University of Geological Sciences, Tashkent, Uzbekistan Author

Keywords:

Keywords: Shargun coal; steam activation; activation temperature; micropores; QSDFT; BET; SEM–EDS; import substitution.

Abstract

Uzbekistan imports almost all of the activated carbon used in industrial water treatment, and coal from the Shargun deposit is an obvious candidate feedstock. An earlier stage of this work established that the raw coal has no micropore network accessible to nitrogen and a surface area of only 12.142 m2/g, so its value as an adsorbent depends entirely on activation. Here the governing parameter of that step — temperature — is examined by comparing two regimes, 600 and 850 °C, each consisting of one hour of pyrolysis followed by one hour of steam activation in the same laboratory rig. Pore structure was determined by nitrogen physisorption at 77.35 K and morphology and composition by SEM–EDS. At 600 °C no micropore network formed: the surface area did not exceed the feedstock value and the modal half-width moved from 2.59 to 7.66 nm, that is, existing pores merely widened. At 850 °C a microporous structure appeared: the surface area reached 33.704 m2/g, the modal half-width fell to 1.66 nm, and uptake at a relative pressure of 0.053 was 7.94 cm3/g against 0.167 for the raw coal, a factor of 47.5. Over the common width range 0.74–5.53 nm the activated sample exceeds the feedstock by 1.67 times in pore volume and by 6.7 times in surface area. The BET equation failed for both samples but for opposite reasons: C = 1.799 for the raw coal and C = −36.725 for AC-850. The working regime should therefore be built around 850 °C, and the reported surface area is a lower bound, since the micropore filling region was not sampled.

References

1. Resolution of the President of the Republic of Uzbekistan “On measures for the development of renewable and hydrogen energy in the Republic of Uzbekistan”, No. PQ-5063. – Tashkent, 9 April 2021. – lex.uz.

2. Decree of the President of the Republic of Uzbekistan “On the Uzbekistan – 2030 Strategy”, No. PF-158. – Tashkent, 11 September 2023. – lex.uz.

3. Kang D., Kim J., Kim D., Kim S. The effect of water treatment processes on the performance of proton exchange membrane water electrolysis // Water. – 2026. – Vol. 18, No. 10. – Art. 1213. – DOI: 10.3390/w18101213.

4. Luukkonen T., Tolonen E.-T., Runtti H. et al. Removal of total organic carbon (TOC) residues from power plant make-up water by activated carbon // Journal of Water Process Engineering. – 2014. – Vol. 3. – P. 46–52. – DOI: 10.1016/j.jwpe.2014.08.005.

5. Salikhanova D., Usmonova Z., Sobirjonova S., Ubaydullaeva N., Karabayeva M. Obtainment of activated carbon by processing plum stones and using them in industrial wastewater purification // E3S Web of Conferences. – 2024. – Vol. 486. – Art. 01017. – DOI: 10.1051/e3sconf/202448601017.

6. Marsh H., Rodríguez-Reinoso F. Activated Carbon. – Amsterdam: Elsevier, 2006. – 536 p.

7. Xiong S., Lv F., Wang C. et al. Coal-based activated carbon prepared by H2O activation process for supercapacitors using response surface optimization method // Frontiers of Chemical Science and Engineering. – 2024. – Vol. 18. – Art. 63. – DOI: 10.1007/s11705-024-2422-4.

8. Zhang L., Zuo S. The significance of lignocellulosic raw materials on the pore structure of activated carbons prepared by steam activation // Molecules. – 2024. – Vol. 29, No. 13. – Art. 3197. – DOI: 10.3390/molecules29133197.

9. Thommes M., Kaneko K., Neimark A.V. et al. Physisorption of gases, with special reference to the evaluation of surface area and pore size distribution (IUPAC Technical Report) // Pure and Applied Chemistry. – 2015. – Vol. 87, No. 9–10. – P. 1051–1069. – DOI: 10.1515/pac-2014-1117.

10. Rouquerol J., Llewellyn P., Rouquerol F. Is the BET equation applicable to microporous adsorbents? // Studies in Surface Science and Catalysis. – 2007. – Vol. 160. – P. 49–56.

11. Neimark A.V., Lin Y., Ravikovitch P.I., Thommes M. Quenched solid density functional theory and pore size analysis of micro-mesoporous carbons // Carbon. – 2009. – Vol. 47, No. 7. – P. 1617–1628. – DOI: 10.1016/j.carbon.2009.01.050.

12. Landers J., Gor G.Y., Neimark A.V. Density functional theory methods for characterization of porous materials // Colloids and Surfaces A. – 2013. – Vol. 437. – P. 3–32. – DOI: 10.1016/j.colsurfa.2013.01.007.

13. Kwiatkowski M. An analysis of the textural properties of activated carbons obtained from biomass via the LBET, NLDFT and QSDFT methods // Scientific Reports. – 2024. – Vol. 14. – Art. 26472. – DOI: 10.1038/s41598-024-76297-x.

14. Anvarova I. Determination of the adsorption properties of activated carbon obtained from local raw materials for the regeneration of amine solutions used in natural gas treatment // Journal of Integrated Education and Research. – 2022. – Vol. 1, No. 6. – P. 90–93. (in Uzbek)

Downloads

Published

2026-09-22